NEOiD Dante to Line
Converts two Dante network channels into two balanced analog XLR outputs, with PoE power.
- Simultaneous channels
- 2 outputs
- Maximum output level
- 12 dBu (balanced)
- THD+N
- ≤ 0.005% @ 12 dBu, 1 kHz
- Noise floor
- < −90 dBu
Overview
The NEOiD Dante to Line brings audio from the Dante network to any amplifier. Its two balanced XLR outputs deliver line-level signal with a maximum level of 12 dBu and THD+N up to 0.005%, ready for amplifiers, powered speakers, stage monitors, and recorders. The 3.5 mm headphone output, with dedicated volume, allows you to check the output signal. Powered by PoE (802.3af/at) or a 12 V DC power supply, it works with a single network cable and operates with 24-bit audio, compatible with AES67.
Features
- 2 XLR outputs
- Balanced
- THD+N ≤ 0.005%
- PoE
Technical specifications
Operation mode
- Operation mode
- Dante → Analog
- Simultaneous channels
- 2 outputs
Audio outputs
- Analog outputs
- 2× balanced male XLR
- Maximum output level
- 12 dBu (balanced)
- Output impedance
- 150 Ω balanced · 75 Ω unbalanced
Audio performance
- THD+N
- ≤ 0.005% @ 12 dBu, 1 kHz
- Noise floor
- < −90 dBu
- Frequency response
- 20 Hz – 20 kHz (±1 dB)
- Signal-to-noise ratio
- ≥ 96 dB
- Crosstalk
- ≥ 70 dB
Network & Dante
- Dante port (RJ-45)
- 1× RJ-45 (100 Mbps)
- PoE (Power over Ethernet)
- Yes
- Sample rate / bit depth
- 44.1 / 48 / 88.2 / 96 kHz · 24-bit (44.1 and 88.2 kHz with a firmware update)
- Dante latency
- 1, 2 or 5 ms (via Dante Controller)
- AES67
- Yes
Control & monitoring
- Controls
- Monitor volume
- Monitor selection
- Output
- Headphone output (3.5 mm TRS)
- 30 mW @ 32 Ω (stereo)
- LED indicators
- Power · Link/Act · Speed
Physical & power
- Power
- PoE (802.3af/at) or DC 12 V
- Power consumption
- ≤ 1.5 W
- Weight
- 0.22 kg
- Dimensions (W × H × D)
- 109 × 70 × 36 mm
- Operating temperature
- −10 °C to 50 °C
Compare with products in the same category
| Compared item | NEOiD Dante to Line | NEOiD Line to Dante | NEOiD Mic to Dante | NEOiD Dante 16×16 |
|---|---|---|---|---|
| Summary | Converts two Dante network channels into two balanced analog XLR outputs, with PoE power. | Takes two line audio channels to the Dante network, with combo XLR/TRS inputs and PoE power. | Converts two microphones or line sources to the Dante network, with 10 to 40 dB preamp, +48 V phantom and PoE. | Dante interface with 16 analog inputs and 16 outputs to integrate analog equipment into the network. |
| Operation mode | Dante → Analog | Analog → Dante | Analog → Dante | not provided |
| Simultaneous channels | 2 outputs | 2 inputs | 2 inputs | not provided |
| THD+N | ≤ 0.005% @ 12 dBu, 1 kHz | ≤ 0.005% @ 12 dBu, 1 kHz | ≤ 0.005% @ 12 dBu, 1 kHz | not provided |
| Published files | no files | no files | no files | no files |
Need help with this product?
Open a ticket and our support team takes it from here. Include the model and, if you have it, the device serial number.
Describe the problem now; to send it, sign in or create an account.